Materials
Pick the plastic by the job, not the catalog.
13 plastics are priced online, plus 6061 and brass. The notes are the ones you would get on the phone: what it is for, why it works, and the thing that bites people. Not sure which one? Parts by type starts from the part, or call 847-260-8104 and say what it does.
Machining and routing stock
| Material | Grades | Good for | Why it works | Watch out for | Standard tolerance | Sheet for routing |
|---|---|---|---|---|---|---|
| Delrin / Acetal (POM) | Acetal copolymer — natural · Acetal copolymer — black · Delrin 150 homopolymer — natural · Delrin 150 homopolymer — black | Bushings, gears, wear parts, housings. The usual first choice for a machined plastic part. | Stiff, low friction, cuts cleanly and holds size. Homopolymer (Delrin) is a little stiffer; copolymer has less centerline porosity in thick rod. | Not for chlorine or strong acids. Food-contact compliance depends on the maker's grade, not on the color. | ±0.005" | 1/16"–3/4" |
| UHMW Polyethylene | UHMW — natural · UHMW — black | Conveyor guides, wear strips, chute liners, cutting-board duty. | Among the most abrasion-resistant unfilled plastics. Very slippery, takes impact, cheap. | Soft and springy under the cutter, so tolerances are looser than acetal. Moves with temperature on long parts. | ±0.010" | 1/16"–1" |
| HDPE | HDPE — natural · HDPE — black | Trays, totes, tanks, cutting boards, marine and outdoor parts. | Cheap, tough, chemical-resistant. Routes fast from sheet. | Low stiffness; not for close-tolerance parts. Nothing sticks to it, including paint. | ±0.010" | 1/16"–1" |
| Nylon | Nylon 6/6 extruded — natural · Cast Nylon 6 — natural · Nylon 6/6 — black · Nylon MD / oil-filled (Nylatron-type) | Gears, sprockets, rollers, bearings, sheaves, structural parts that get hit. | Strong and tough with good wear life. Cast nylon for big blocks; oil-filled grades for dry bearings. | Absorbs moisture and grows, up to about 2% in length when saturated. Say whether the part runs wet. | On the quote | 1/16"–1" |
| PEEK | PEEK — natural (unfilled) | High-heat seals, bushings and insulators; pump and valve parts. | Keeps its strength hot (480 °F long-term on the maker's datasheet), resists most chemicals, wears well, holds size. | Expensive stock. The material is most of the price, so send the drawing and the stock can be sized close. | On the quote | Rod / block |
| Ultem (PEI) | Ultem 1000 — amber | Electrical insulators, high-temperature fixtures, parts that get sterilized. | Stiff and strong when warm (338 °F long-term on the maker's datasheet), a good insulator, transparent amber. | Notch-sensitive. Keep inside corners radiused. | On the quote | Rod / block |
| PTFE (Teflon) | PTFE virgin — white | Seals, seats, slide pads, chemical-service parts, electrical insulators. | Very low friction, and almost nothing attacks it. | Soft, creeps under load, tolerances are wide. Filled grades (glass, bronze) for wear. | On the quote | Rod / block |
| Polycarbonate | Polycarbonate — clear · Polycarbonate — black | Machine guards, windows, covers. | Clear, with very high impact strength. The usual choice for a guard that must not shatter. | Scratches, and crazes with some solvents and cleaners. A cut face comes off the cutter frosted, not clear. | On the quote | 1/16"–1/2" |
| Acrylic (cast) | Cast acrylic — clear | Displays, windows, light guides, cosmetic covers. | Optically clear and harder to scratch than polycarbonate. | Brittle. Radius the corners and don't over-tighten fasteners. Cast, not extruded, for machining. | On the quote | 1/16"–1" |
| PVC Type 1 | PVC Type 1 — gray | Chemical tanks and manifolds, duct, fixtures, signage (expanded PVC). | Cheap, chemical-resistant, solvent-weldable, easy to machine. | Gray Type 1 for structural; expanded PVC is light and soft, not for load. | On the quote | 1/16"–1" |
| Polypropylene | Polypropylene homopolymer — natural | Tanks, chemical fixtures, cutting boards, lab parts. | Resists most acids and bases, light, cheap, weldable. | Flexible and hard to hold to a close tolerance. Warps if cut unevenly. | On the quote | 1/16"–1" |
| G-10 / FR-4 Glass Epoxy | G-10 — natural green · FR-4 — yellow | Electrical insulators, test fixtures, structural plates. | Very stiff and strong, holds size, a good insulator. | Abrasive. It eats tooling, so it prices above the thermoplastics, and the dust has to be collected. | On the quote | 1/16"–1/2" |
| Canvas Phenolic (CE) | Canvas phenolic CE — brown · Linen phenolic LE | Wear pads, gears, insulators, bearing retainers, test fixtures. | Stiff, cheap insulator with good wear life. | Abrasive, and edges can fray on through-holes. | On the quote | 1/16"–1" |
| Aluminum 6061-T6 | 6061-T6 | Brackets, plates, housings, fixtures: anything that mates with metal. | Light, stiff, machines fast, anodizes. | For heavy aluminum production you may be better served by a dedicated metal shop. | On the quote | 1/16"–1/2" |
| Brass 360 (Free-machining) | C360 | Fittings, bushings, electrical contacts. | Free-machining, corrosion-resistant, conductive. | Heavy and not cheap. | On the quote | Rod / block |
3D printing materials
FDM filaments, and SLA in Formlabs Grey, White, Clear, Tough 1500, Tough 2000, Rigid 10K, High Temp and ESD resins at 0.1 mm or 0.05 mm layers.
PLAABSPETGNylon (PA12)TPU (Flexible)Carbon Fiber NylonGrey resin (SLA)White resin (SLA)Clear resin (SLA)Tough 1500 resin (SLA)Tough 2000 resin (SLA)Rigid 10K resin (SLA)High Temp resin (SLA)ESD resin (SLA)
Part touches food?
Food-contact compliance belongs to a specific grade from a specific maker, not to a plastic or a color. What a machine shop can and cannot certify.
Need a material that isn't listed?
Vespel, Torlon, PPS, PVDF, filled grades, stock you supply: ask. If we haven't cut it before, we'll say so.