Plastics machine shop · Wauconda, Illinois847-260-8104
Material

UHMW polyethylene machining and routing

UHMW-PE (ultra-high-molecular-weight polyethylene) is a soft, very slippery, highly abrasion-resistant plastic. It takes impact without cracking and absorbs almost no water. It is used where parts slide, rub or get hit, and where holding a tight dimension matters less than wear life.

Upload a STEP or STL and the price shows in a few seconds; no account needed. Up to 100 pieces checks out by card. Above that a person quotes it within 24 hours. Questions: 847-260-8104 rings the shop.

What UHMW is used for

  • Conveyor guides, wear strips and lane dividers
  • Chute, hopper and bin liners
  • Guide rails and corner tracks on packaging lines
  • Bumpers, slide pads and dock components
  • Cutting and work surfaces

How it is priced here

  • CNC milling from plate and rod. Grades quoted online: UHMW — natural; UHMW — black.
  • CNC routing from sheet, 1/16" to 1" thick (1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1"). Sheet grades quoted online: UHMW — natural; UHMW — black.
  • Size limits and design rules are on the machining and routing pages.

Typical properties

PropertyUHMW-PE (PE 1000)
Density0.93 g/cm³
Tensile strength19 MPa at yield, about 2,750 psi (ISO 527)
Max service temperature (air)up to 80 °C (176 °F)
Water absorption0.01% (ISO 62)
Coefficient of frictionNot listed on the datasheet
SourceEnsinger TECAFINE PE1000 natural (datasheet values, retrieved 2026-11-09)

Typical values from the datasheet named above, for unfilled natural material at room temperature. They are not a specification. Grades, colors, fillers and stock makers differ, so confirm against the datasheet for the grade you will actually buy before designing to a number.

Wear and friction

Among the most abrasion-resistant unfilled plastics and very low friction against steel, which is why it is the standard wear-strip material. The datasheet above does not list a friction coefficient.

Food contact

Natural UHMW is widely sold with FDA and EU 10/2011 food-contact statements from the stock manufacturer (the datasheet cited above makes that statement for its product). Black and reprocessed grades usually are not.

Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to. More on food-contact plastics.

Machining notes

  • Soft and springy. It pushes away from the cutter and tends to leave a fuzzy burr, so sharp tools and a clean-up pass matter more than on acetal.
  • Thermal expansion is high (roughly ten times that of steel). A long strip measured in a cold shop and installed on a warm line will be a different length; dimension long parts with that in mind.
  • Sheet is skived or pressed and is rarely flat; thick sheet can move when one face is machined away. Flatness callouts on large UHMW parts should be generous.
  • It will not hold a fine thread well and cannot be glued. Use through-bolts, inserts or mechanical capture.
  • Realistic tolerances are looser than for acetal. If a dimension on a UHMW part is critical, call it out on the drawing so it can be reviewed before the job is quoted.

Common questions

What forms of UHMW do you quote online?
CNC milling from plate and rod, and CNC routing from sheet 1/16" to 1" thick. Sheet thicknesses quoted online: 1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1". Other sizes and grades can be requested on a firm quote.
What tolerance is realistic on UHMW?
UHMW is soft and moves with temperature, so realistic tolerances are looser than for acetal or nylon. Standard tolerance on UHMW here is ±0.010". On UHMW, call out any critical dimension so it is reviewed on a firm quote rather than assumed.
Is UHMW suitable for food contact?
Natural UHMW is widely sold with FDA and EU 10/2011 food-contact statements from the stock manufacturer (the datasheet cited above makes that statement for its product). Black and reprocessed grades usually are not. Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to.
How do I get a price for a part in UHMW?
Upload a STEP or STL file to the quote builder and choose UHMW-PE. Quantities up to 100 pieces are priced online; larger quantities and parts that need review get a firm quote from a person within 24 hours.

Price your UHMW part now

Upload a STEP or STL with UHMW-PE already selected. No account needed to see a price.

Other materials