Plastics machine shop · Wauconda, Illinois847-260-8104
Material

Nylon 6/6 and cast nylon machining

Nylon (polyamide) is a strong, tough bearing and wear plastic. Extruded nylon 6/6 is the common rod and plate grade; cast nylon 6 is used for larger blocks, plates and rounds. Both absorb moisture from the air and change size as they do, which is the main thing to design around.

Upload a STEP or STL and the price shows in a few seconds; no account needed. Up to 100 pieces checks out by card. Above that a person quotes it within 24 hours. Questions: 847-260-8104 rings the shop.

What nylon is used for

  • Gears, sprockets and sheaves
  • Rollers, wheels and bushings
  • Wear pads and slide blocks under load
  • Structural spacers and insulators that take impact
  • Large rings and blocks (cast nylon)

How it is priced here

  • CNC milling from plate and rod. Grades quoted online: Nylon 6/6 extruded — natural; Cast Nylon 6 — natural; Nylon 6/6 — black; Nylon MD / oil-filled (Nylatron-type).
  • CNC routing from sheet, 1/16" to 1" thick (1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1"). Sheet grades quoted online: Nylon 6/6 — natural; Cast Nylon 6.
  • Size limits and design rules are on the machining and routing pages.

Typical properties

PropertyNylon 6/6, extrudedCast nylon 6
Density1.14 g/cm³1.14 g/cm³
Tensile strength12,000 psi at yield (ASTM D638)12,000 psi at yield (ASTM D638)
Max service temperature (air)185 °F long term; 300 °F short term200 °F long term; 300 °F intermittent
Water absorption0.45% in 24 h; 8.5% at saturation (ASTM D570)1.2% in 24 h; 5.5% at saturation (ASTM D570)
Coefficient of friction0.26 dynamic (ASTM D3702)0.26 dynamic (ASTM D3702)
SourceEnsinger TECAMID 66 natural (datasheet values, retrieved 2026-11-09)Ensinger TECAST T natural (datasheet values, retrieved 2026-11-09)

Typical values from the datasheet named above, for unfilled natural material at room temperature. They are not a specification. Grades, colors, fillers and stock makers differ, so confirm against the datasheet for the grade you will actually buy before designing to a number.

Wear and friction

Good wear life and load capacity for an unfilled plastic. Oil-filled and molybdenum-disulfide-filled grades are sold for bearings that run dry.

Food contact

Some natural nylon 6/6 and cast nylon grades are offered with FDA food-contact statements; filled and lubricated grades generally need to be checked individually.

Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to. More on food-contact plastics.

Machining notes

  • Machines well with sharp tools but is tougher and stringier than acetal; burrs take more work to remove.
  • Moisture is the main issue. Nylon takes up water from the air over weeks and grows as it does, so a part can be in tolerance when machined and measurably larger in humid or wet service. Say what environment the part lives in.
  • Because of that, very tight tolerances on nylon are only meaningful if the measurement condition is stated. Call out the dimensions that matter on a firm-quote request, and the tolerance for them is agreed before you order.
  • Cast nylon has lower internal stress than extruded and is the better choice for large or thick parts and for parts with a lot of material removed.
  • For a part that must hold size in wet service, acetal is usually the better material.

Common questions

What forms of nylon do you quote online?
CNC milling from plate and rod, and CNC routing from sheet 1/16" to 1" thick. Sheet thicknesses quoted online: 1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1". Other sizes and grades can be requested on a firm quote.
What tolerance is realistic on nylon?
Nylon absorbs moisture and grows, so a tolerance on nylon needs a stated condition (as machined and dry, or conditioned). Call out the dimensions that matter on a firm-quote request, and the tolerance for them is agreed before you order. If the part runs wet or humid, say so on the request.
Is nylon suitable for food contact?
Some natural nylon 6/6 and cast nylon grades are offered with FDA food-contact statements; filled and lubricated grades generally need to be checked individually. Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to.
How do I get a price for a part in nylon?
Upload a STEP or STL file to the quote builder and choose Nylon 6/6 and cast nylon 6. Quantities up to 100 pieces are priced online; larger quantities and parts that need review get a firm quote from a person within 24 hours.

Price your nylon part now

Upload a STEP or STL with Nylon 6/6 and cast nylon 6 already selected. No account needed to see a price.

Other materials