Plastics machine shop · Wauconda, Illinois847-260-8104
Material

HDPE routing and machining

HDPE (high-density polyethylene) is an inexpensive, tough, chemical-resistant sheet plastic. It is lighter than water, absorbs essentially none of it, and is easy to cut in volume. It is not stiff and not a precision material; it is chosen for cost, toughness and chemical resistance.

Upload a STEP or STL and the price shows in a few seconds; no account needed. Up to 100 pieces checks out by card. Above that a person quotes it within 24 hours. Questions: 847-260-8104 rings the shop.

What HDPE is used for

  • Trays, nests, totes and dunnage
  • Cutting boards and food-prep surfaces
  • Tank, splash and chemical-area parts
  • Outdoor and marine panels (marine-board grades)
  • Spacers, shims and low-load wear parts

How it is priced here

  • CNC milling from plate and rod. Grades quoted online: HDPE — natural; HDPE — black.
  • CNC routing from sheet, 1/16" to 1" thick (1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1"). Sheet grades quoted online: HDPE — natural; HDPE — black; HDPE marine board (King StarBoard-type).
  • Size limits and design rules are on the machining and routing pages.

Typical properties

PropertyHDPE
Density0.95 g/cm³
Tensile strength3,700 psi at yield (ASTM D638)
Max service temperature (air)Listed as 248 °F long-term maximum. Heat deflection temperature is 167 °F at 66 psi (ASTM D648), so loaded parts soften far below the listed maximum.
Water absorptionNot listed on the datasheet
Coefficient of frictionNot listed on the datasheet
SourceEnsinger TECAFINE HDPE natural (datasheet values, retrieved 2026-11-09)

Typical values from the datasheet named above, for unfilled natural material at room temperature. They are not a specification. Grades, colors, fillers and stock makers differ, so confirm against the datasheet for the grade you will actually buy before designing to a number.

Wear and friction

Slippery and reasonably wear-resistant, but well short of UHMW. For a sliding part that sees real abrasion, UHMW is the usual upgrade. The datasheet above describes moisture absorption only as "low" and does not list a friction coefficient.

Food contact

Natural HDPE sheet is commonly sold with FDA food-contact statements and is the usual cutting-board material; colored and marine-board grades vary by manufacturer.

Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to. More on food-contact plastics.

Machining notes

  • Cuts fast and cleanly on a router with sharp single-flute tooling. Chips are stringy and edges can carry a light burr that is trimmed after cutting.
  • Low stiffness and high thermal expansion. It is not a material for tight tolerances or for parts that must stay flat over a long span.
  • Sheet has residual stress from extrusion. Deep pockets or heavy one-sided cuts can let a part cup; balanced pocketing and leaving a floor thicker than a third of the sheet helps.
  • Paint, adhesive and most inks do not stick to it. Mark by engraving and join with fasteners or plastic welding.

Common questions

What forms of HDPE do you quote online?
CNC milling from plate and rod, and CNC routing from sheet 1/16" to 1" thick. Sheet thicknesses quoted online: 1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4", 1". Other sizes and grades can be requested on a firm quote.
What tolerance is realistic on HDPE?
HDPE is soft and expands with temperature, so it is not a precision material. Standard tolerance on HDPE here is ±0.010".
Is HDPE suitable for food contact?
Natural HDPE sheet is commonly sold with FDA food-contact statements and is the usual cutting-board material; colored and marine-board grades vary by manufacturer. Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to.
How do I get a price for a part in HDPE?
Upload a STEP or STL file to the quote builder and choose HDPE. Quantities up to 100 pieces are priced online; larger quantities and parts that need review get a firm quote from a person within 24 hours.

Price your HDPE part now

Upload a STEP or STL with HDPE already selected. No account needed to see a price.

Other materials