PTFE machining
PTFE (polytetrafluoroethylene; Teflon is the best-known brand) has very low friction, a very wide temperature range and resistance to almost all chemicals. It is also soft, weak and creeps under load. It is chosen for chemical, thermal or sliding duty, not for strength.
Upload a STEP or STL and the price shows in a few seconds; no account needed. Up to 100 pieces checks out by card. Above that a person quotes it within 24 hours. Questions: 847-260-8104 rings the shop.
What PTFE is used for
- Seals, gaskets and valve seats
- Slide pads and low-friction liners
- Chemical-service fittings and spacers
- High-temperature and high-frequency electrical insulators
How it is priced here
- CNC milling from plate and rod. Grades quoted online: PTFE virgin — white.
- Not quoted online as routed sheet. Ask on a firm quote if you need flat parts from sheet.
- Size limits and design rules are on the machining and routing pages.
Typical properties
| Property | PTFE, virgin |
|---|---|
| Density | 2.15 g/cm³ |
| Tensile strength | 22 MPa, about 3,200 psi (ASTM D4894) |
| Max service temperature (air) | 260 °C (500 °F) |
| Water absorption | 0.01% (ASTM D570) |
| Coefficient of friction | Not listed on the datasheet |
| Source | Ensinger TECAFLON PTFE natural (datasheet values, retrieved 2026-11-09) |
Typical values from the datasheet named above, for unfilled natural material at room temperature. They are not a specification. Grades, colors, fillers and stock makers differ, so confirm against the datasheet for the grade you will actually buy before designing to a number.
Wear and friction
Very low friction, but unfilled PTFE wears quickly and cold-flows under sustained load. Glass-, carbon- and bronze-filled grades are sold for wear and creep resistance. The datasheet above does not list a friction coefficient.
Food contact
Virgin PTFE is commonly sold with FDA food-contact statements from the stock manufacturer; filled grades need to be checked individually.
Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to. More on food-contact plastics.
Machining notes
- Cuts easily but is very soft. It deflects under clamping and cutting pressure, so parts are held lightly and thin walls are hard to keep round.
- It has a volume change near room temperature (around 66 °F / 19 °C) and high thermal expansion, so a measurement depends on the temperature it is taken at.
- It creeps under load. A dimension that is right after machining can relax under a clamped joint or a press fit.
- For those reasons, realistic tolerances on PTFE are wide. If a dimension is critical, call it out so it is reviewed before the job is quoted.
- It cannot be glued without special surface treatment.
Common questions
- What forms of PTFE do you quote online?
- CNC milling from plate and rod. Other sizes and grades can be requested on a firm quote.
- What tolerance is realistic on PTFE?
- PTFE is soft, creeps and changes size with temperature, so tolerances are wider than for rigid plastics. Call out the dimensions that matter on a firm-quote request, and the tolerance for them is agreed before you order. On PTFE, call out any critical dimension so it is reviewed on a firm quote rather than assumed.
- Is PTFE suitable for food contact?
- Virgin PTFE is commonly sold with FDA food-contact statements from the stock manufacturer; filled grades need to be checked individually. Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to.
- How do I get a price for a part in PTFE?
- Upload a STEP or STL file to the quote builder and choose PTFE. Quantities up to 100 pieces are priced online; larger quantities and parts that need review get a firm quote from a person within 24 hours.
Price your PTFE part now
Upload a STEP or STL with PTFE already selected. No account needed to see a price.