Plastics machine shop · Wauconda, Illinois847-260-8104
Material

Acetal and Delrin (POM) machining

Acetal (polyoxymethylene, POM) is a stiff, low-friction, dimensionally stable engineering plastic. It is sold as copolymer (often just called acetal) and as homopolymer (Delrin is the best-known brand). It absorbs little water and cuts cleanly, which makes it a common first choice for machined plastic parts.

Upload a STEP or STL and the price shows in a few seconds; no account needed. Up to 100 pieces checks out by card. Above that a person quotes it within 24 hours. Questions: 847-260-8104 rings the shop.

What acetal is used for

  • Bushings, bearings, rollers and wear pads
  • Gears, cams and sprockets under light to moderate load
  • Clamps, saddles, brackets and fixture blocks
  • Manifolds, valve bodies and housings
  • Spacers, standoffs and electrical insulators

How it is priced here

  • CNC milling from plate and rod. Grades quoted online: Acetal copolymer — natural; Acetal copolymer — black; Delrin 150 homopolymer — natural; Delrin 150 homopolymer — black.
  • CNC routing from sheet, 1/16" to 3/4" thick (1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4"). Sheet grades quoted online: Acetal — natural; Acetal — black.
  • Size limits and design rules are on the machining and routing pages.

Typical properties

PropertyAcetal copolymer (POM-C)Acetal homopolymer (POM-H, Delrin resin)
Density1.41 g/cm³1.41 g/cm³
Tensile strength9,300 psi at yield (ASTM D638)11,000 psi at yield (ASTM D638)
Max service temperature (air)195 °F long term; 285 °F intermittent185 °F long term; 300 °F intermittent
Water absorption0.18% in 24 h; 0.80% at saturation (ASTM D570)0.25% in 24 h; 0.90% at saturation (ASTM D570)
Coefficient of friction0.21 dynamic (ASTM D3702)0.20 dynamic (ASTM D3702)
SourceEnsinger TECAFORM AH natural (datasheet values, retrieved 2026-11-09)Ensinger TECAFORM AD natural (datasheet values, retrieved 2026-11-09)

Typical values from the datasheet named above, for unfilled natural material at room temperature. They are not a specification. Grades, colors, fillers and stock makers differ, so confirm against the datasheet for the grade you will actually buy before designing to a number.

Wear and friction

Low friction against steel and good wear life without lubrication. Homopolymer is somewhat stiffer and stronger; copolymer is less prone to centerline porosity in thick rod and plate and holds up better in hot water and alkaline cleaners.

Food contact

Natural (unpigmented) acetal grades are commonly offered by stock manufacturers with FDA food-contact compliance statements; black and filled grades often are not.

Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to. More on food-contact plastics.

Machining notes

  • One of the easiest plastics to machine. It forms a clean chip, takes a good finish straight off the cutter and deburrs easily.
  • Dimensionally stable for a plastic, so it is the usual choice when a plastic part needs to hold a dimension. Standard tolerance on Acetal / Delrin here is ±0.005"; the tightest quoted is ±0.002" on a called-out feature.
  • Thick plate and large-diameter rod carry internal stress from extrusion. Removing a lot of material from one side can let a part bow; roughing both sides and letting the part rest before the finish pass reduces this.
  • Homopolymer rod and plate can have centerline porosity. If a part is cut through the middle of thick stock and the surface there matters (seal faces, pressure passages), ask for copolymer.
  • Not suitable for strong acids or chlorine service. It cannot be reliably glued; design for fasteners or press fits.

Common questions

What forms of acetal do you quote online?
CNC milling from plate and rod, and CNC routing from sheet 1/16" to 3/4" thick. Sheet thicknesses quoted online: 1/16", 1/8", 3/16", 1/4", 3/8", 1/2", 3/4". Other sizes and grades can be requested on a firm quote.
What tolerance is realistic on acetal?
Acetal is among the most dimensionally stable of the common machined plastics. Standard tolerance on Acetal / Delrin here is ±0.005"; the tightest quoted is ±0.002" on a called-out feature. Tighter requests are reviewed on a firm quote with the drawing.
Is acetal suitable for food contact?
Natural (unpigmented) acetal grades are commonly offered by stock manufacturers with FDA food-contact compliance statements; black and filled grades often are not. Food-contact status belongs to a specific grade, color and lot from the stock manufacturer, not to the polymer family. If your part touches food or drinking water, say so on the quote request and name the regulation your customer cites. You will be told before you order what paperwork can be had for that stock. A machine shop cannot certify a finished part for food contact, and this one does not claim to.
How do I get a price for a part in acetal?
Upload a STEP or STL file to the quote builder and choose Acetal / Delrin (POM). Quantities up to 100 pieces are priced online; larger quantities and parts that need review get a firm quote from a person within 24 hours.

Price your acetal part now

Upload a STEP or STL with Acetal / Delrin (POM) already selected. No account needed to see a price.

Other materials